HVAC control and BMS
We design, programme and commission the control of chillers, boilers, air handling units, fan coil units and heat recovery units, with supervision from any device.
View service
Honeywell partner · Extremadura
Buildings that run themselves. And use less energy.
We integrate, migrate and maintain BMS (building management systems) and HVAC control in hospitals, museums, public buildings, hotels and industry across Extremadura and neighbouring provinces in Spain.
Reply within 24 working hours
- Niagara Framework
- BACnet
- Modbus
- KNX
- LonWorks
Official Honeywell partner and technicians certified by Schneider Electric to install their equipment and integrate EcoStruxure Building Operation. We also integrate Siemens Desigo with ABT Site. All of them at once? Yes: there are no rivalries in the plant room, just equipment that has to work together. On every project we choose what best suits your building.
- 15–40%savings on HVAC through optimised control
- 2–4 yearstypical payback period
- 30,000control points integrated
Typical ranges, depending on the initial condition of the installation. Before we start, we give you an estimate based on your building's data.
What we do
From the electrical panel to the supervisory screen, with a single point of contact
Migration of obsolete systems
We replace unsupported controllers (Honeywell CARE/Eagle, KNX and other manufacturers) with open Niagara platforms, reusing the existing wiring, sensors and actuators.
View serviceElectrical and control panels
We build and wire motor control, protection and control panels to REBT (Spanish low-voltage regulation), fully documented and workshop-tested before they reach site.
View electrical panelsEnergy efficiency and solar PV
We fine-tune schedules, setpoints and curves, analyse power quality and install self-consumption solar PV on tiled roofs, flat roofs and industrial buildings.
View serviceEnergy management as a service
We monitor your consumption, send you automated reports and support you with ISO 50001 and carbon footprint calculation.
View serviceRemote monitoring and predictive maintenance
We monitor your installation remotely and analyse its data to anticipate faults before users notice anything is wrong. Training for maintenance staff and users.
View remote monitoringAutomated fault detection (FDD)
Automated rules check your control system every day and alert you to leaking valves, equipment running out of hours or drifting sensors, ranked by impact.
View serviceConsultancy, design and audits
We help engineering firms and building owners define the controls: points list, sequences, bills of quantities, specifications, bid review and audits of existing systems.
View serviceDrone inspection
We inspect high-voltage lines, roofs, solar PV installations and any hard-to-reach area, with no scaffolding and no service interruptions.
View serviceTelecoms, fibre and CCTV
Data networks, racks and switches, fibre optic splicing and testing, IP camera video surveillance and people counters.
View serviceStandards properly applied
UNE, DIN, REBT, RITE, CTE: we love standards and, above all, applying them. Every installation documented and compliant.
View standards
Why ACIPro
Open, documented systems, close to you
- Official Honeywell partner. Direct access to products, training and factory support.
- No vendor lock-in. We work with open protocols (BACnet, Modbus, KNX) and the Niagara platform: anyone will be able to maintain your installation.
- A single point of responsibility. Panels, wiring, programming, graphics and commissioning are all handled by the same team.
- Data with a clear identity. Every point in every installation follows our database of short, readable names and is tagged with the open Project Haystack standard. Your data is ready for analytics and AI.
- Complete documentation. Schematics, points list and maintenance staff training with every handover.
- Obsessed with standards. We love UNE, DIN, ASHRAE, ISA, IEC 62443, the REBT, the RITE and the CTE, and above all we love applying them.
- 3D graphics designed in-house. We model every supervisory graphic to match the actual equipment.
- Technicians based in Extremadura. Fast response across Extremadura and neighbouring provinces in Spain.
Our own 3D graphics
Every screen, custom-modelled
We don't use generic icons. We model every air handling unit, chiller and plant room in 3D exactly as it is in reality, so operators can recognise each piece of equipment at a glance.
How we work
Five steps, from site visit to maintenance
Site visit and audit
We look at the installation, the equipment and what isn't working.
Proposal
Points list, architecture and fixed-price quote.
Workshop
Panels built, programmed and tested before going to site.
Commissioning
Point-to-point testing, graphics and training.
Follow-up
Remote monitoring, predictive maintenance and energy reports.
Find your case
What does your building need?
Choose the problem, solution, brand or sector you're interested in. Each page explains how we solve it, with real cases and FAQs.
PROBLEMS WE SOLVE
SOLUTIONS
- A control-focused energy efficiency company in Extremadura
- Open BMS integration, with no vendor lock-in
- Building management: what it is, what it includes and how to procure it
- Remote monitoring and management of installations in Cáceres, Badajoz and across Extremadura
- Industrial automation in Cáceres and across Extremadura
- Electrical panels and automation in Cáceres and across Extremadura
- BACS requirements for buildings: what the regulations require and how to comply
- Remote monitoring of pumping stations, wells and wastewater treatment plants in Extremadura
- BMS and OT cybersecurity: protecting the control system of your building or plant
- Networks, Wi-Fi, CCTV and fibre optics for buildings and industry
- Services for engineering firms and consultants: controls and BMS
- Building services control for local councils and public bodies
HONEYWELL AND NIAGARA
Regulations
Building controls are now a requirement, not an option
The EU Energy Performance of Buildings Directive requires building automation and control systems in non-residential buildings with high-output HVAC systems (over 290 kW), and the 2024 revision extends the requirement to lower outputs over the coming years. We help you find out whether your building is affected and what class of control it needs under UNE-EN ISO 52120.
And it's not all about obligations: improving your controls can be partly funded through Energy Savings Certificates (CAE, the Spanish scheme). See how it works.
Do you have a control system that nobody knows how to maintain?
We review your installation and tell you what can be reused, what should be replaced and how much you could save.